Support

Tiburon

Operating Instructions

Tiburon

Underwater Camera

Please read this manual thoroughly before operating the
unit, and keep it for future reference.

PRECAUTIONS

• Storage and Keeping

1. Do not expose this equipment to excessive heat or cold place.  The storage

temperature of the monitor is +68°F~+140°F (+20°~+60°C), the operating

temperature is +32°F~104°F (0°C~+40°C)

2. Avoid the machine from dropping or impacting.

3. Never extrude or fraction this machine with sharp objects.

4. Cables are not allowed to touch hot or rotating parts, such as engine,

ventilators, etc.

5. Keep this equipment out of children’s reach.

• Operating Precautions

1. Connect this equipment only to other compatible units.

2. Make sure that all cables are connected properly, Improper connection may

result in system failures or damages to the system.

3. Cables are not to be pinched or stepped on.

4. Remove the cable connections when system is not in use.

5. The camera must not be located directly under the sun or any other bright

light source because this will not only result in a poor image, but also will

eventually damage the electronics of the camera

6. Additional lighting may be required if water quality is poor, or in low light

conditions

• Maintenance

1. Remove all cable connections before cleaning the camera.

2. Wipe off the moisture on the lens of camera regularly.

3. Keep the camera clean and dry when it is not in use.

4. Dry all equipment before storage

LIMITED WARRANTY

 

NavRoute Technologies (“NavRoute”) warrants this product against any defects in materials or workmanship for one year, parts and labor, from the date of purchase, with an original proof of purchase with retailer receipt. If service under this warranty is required, you must return the product to NavRoute for inspection.  You must first obtain a return material authorization (RMA) number from NavRoute Customer Service prior to returning any products. NavRoute Customer Service can be reached at support@theimportsworld.com .  If NavRoute determines that the product is defective, NavRoute will exchange or replace defective parts.

This warranty does not cover:

Products purchased at auctions, or auction sites. 

Damages from misuse, abuse, neglect, or accident, natural disasters, or Acts of God. 

Product which has been electronically or mechanically modified in any way or incorporated into other products. NavRoute is not responsible for any shipping, handling, or insurance charges.

 The remedies hereby provided shall be exclusive remedy of the buyer.  IN NO EVENT SHALL NAVROUTE BE LIABLE FOR ANY INDIRECT, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR SPECIAL DAMAGES, REGARDLESS OF WHETHER A CLAIM FOR SUCH DAMAGES IS BASED ON WARRANTY, CONTRACT, NEGLIGENCE OR OTHERWISE.

 

This warranty gives you specific legal rights and you may have other rights which vary from state to state.  Some states do not allow exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

SPECIFICATIONS

 

Input voltage

12V DC

Image sensor:

Type: COLOR CCD  1/4 SHARP

Sensor Size:

3.6mm×2.7mm

Pixel Resolution:

NTSC:510(H)×492(V)

Lens Angular field of view: 

92degree

Effective focal length:

3.6mm

Resolution:

420 TV lines (H)

Video signal output:

1 V (p-p) composite video signal at 75ohm termination

Led lights:

21pcs

Power Consumption:

more than 48db

Packaging material:

High Impact ABS Plastic

Operating temperature:

-20ºF   +80ºF

Storage Temperature (ºC): 

-20~+60

Product Features

High waterproof and dust proof structure of underwater camera.

21 White LED lights for dark environments

System Connections

Diagram:

Troubleshooting

Symptoms below do not necessarily mean failure with the system.  Please check as following before request for repair.

Symptoms

Possible cause

No Picture

•Use of unauthorized power supply

 Battery low or empty

 Check whether the cables is connected

Dark picture

Check whether power cable is properly connected.

Dim Picture

Check whether the camera lens is dirty

No lights

 Check whether the Power cable is connected.

HOW TO CONNECT THE CAMERA TO THE DVR

Connect the power cables for the camera as show in Camera connection Diagram & connect the video out of the camera to the Female to Female RCA Adapter. After connect this adapter to the video input cable or the DVR unit. As show in the DVR Section in this Manual.

 

 

 

 

If you don't found the information you are looking for please contact us to:

support@theimportsworld.com

 

 

 

 

 

 

 

 

 

 

Copyright © 2010 Navroute Technologies All Rights Reserved.