Support

Octopus Panning Camera

Operating Instructions

 

Octopus

Octupus

Underwater Camera

Please read this manual thoroughly before operating the
unit, and keep it for future reference.

 

Introduction
Underwater camera is designed to connect to your TV, VCR, LCD TV or some Digital Video cameras/camcorders with an A/V input.

The underwater camera is ideal for using on your home TV or VCR (when using underwater camera in the pool) or can be used on TV’s found on cruise or dive boats, 12 portable VCR or LCD monitors (with RCA input)

The underwater camera has the following features:
1. The camera equips with 18 LED lights.
2. It can control the rotation of motor within 360 degree,   then transfer it to the center thus it inverses, such action will repeat until you press the button to make it turn to hand-control.

Camera component description

 

Wire Keyboard
Functions of wire keyboard(PAN CONTROL):(The length of the line is about 750 mm)
Key 1: Automatic / manual switch
Key 2: OSD:Press once, the characters will display on the screen, press again, the character will disappear.
Key 3:SPEED / RIGHT:Under manual mode, press it, the camera will rotate to the right without stop; press again, it will stop rotating. under automatic mode, press once sino-speed, press twice high speed, and press three times low speed. Press more it will cycle.
Key4:LED ON/OFF: press once, the LED are off; press again, the LED are on.
Key5: LEFT/LEFT:under the manual mode, press it, the cameras will rotate to the left without stop; press again, it will stop rotating. under the automatic mode, it is no use.

Note: under the manual mode, press the key 4 and key 2 also can stop the rotating of the camera, press the either key 3 or key 5, the rotating will be realized again.
How to Operate:
After you have connected the cable and the power is getting through. then the initialization process of samples is: all lights are off, no characters. Motor automatically turns left to the center with high speed. Beneath the display, all the lights are on, and then there is an “S” expressing the revolving speed, the depth and the temperature. Motor inverted 360 degrees to the center position, after the inversion, such operation will cycle.

 

Important Information

  1. The camera must not be located under the strong sun directly or any other bright light source as this will not only result in a poor image, but will eventually damage the electronics of the camera.
  2. The camera has been tested waterproof to a depth of 50 meters. Any use below this depth will void the camera’s warranty.
  3. Always wash the camera in warm water and soap after using, to remove salt and other corrosive agents.
  4. Always use appropriate water safety precautions when operating the Underwater Camera, and ensure appropriate level of supervision of children when near water.
  5. Be care with the body of the camera, it is easy to scrape, otherwise it will result in a poor image.

Technical Specifications:

     Image Sensor

1/4 COLOR CCD

 

SYSTEM

PAL/NTSC

 

MODEL

SHARP

 

PIXEL

NTSC:510*492
PAL:500*582

 

VIEWING ANGLE(°)

92°(OPTIONAL)

 

LENS DIMENSION

3.6MM(OPTIONAL)

 

MINIMAL ILLUMINATION

1.0LUX

 

 DISPLAYANGLE (°)

0°-360°

 

 DISPLAY TEMPERATURE(℃)

-50--200 ℃

 

CIRCUMGYRATE

0°-360°

 

VIDEO OUTPUT

1.0VP-P 75Ω

 

POWER SUPPLY

DC 12V

 

POWER CONSUMPTION

1.4W

 

HORIZONTAL RESOLUTION

420 TV LINES

 

WORKING TEMPERATURE(℃)

-10--+50 ℃

 

STORAGE TEMPERATURE(℃)

20 – +60℃

 

S/N RATIO

≥48dB

 

Measurable temperature

-40℃ - +80℃ (accuracy: +/- 2℃)

Measurable depth

MAX:50m

Rotary Speed

S: 3º/s,  SS:6.4º/s,  SSS:11.6º/s

G. W.(KG)

3.0kg

N. W.(KG)

2.6kg

 

 

If you don't found the information you are looking for please contact us to:

support@theimportsworld.com

 

 

 

 

 

 

 

 

 

 

Copyright © 2010 Navroute Technologies All Rights Reserved.